TITAN Machinery Titan Machinery
Contact Us
Chapter 1.1Hyperpress

Hyperpress (High-Pressure Brick and Block Making Machine): Physics, Construction and Operation

A hyperpress forms bricks and blocks from semi-dry mixes at 24.5 MPa or more. Learn the physics, press construction, operating cycle, sizing and defects.

Level
Intermediate
Reading time
15 min
Updated
Written by
TITAN engineering team
Cut-away front view of a four-column double-action hyperpress: upper and lower cylinders drive two punches into a fixed mould while the tie columns carry the force
Cut-away front view of a four-column double-action hyperpress: upper and lower cylinders drive two punches into a fixed mould while the tie columns carry the force
In this chapter you will learn
  • Define hyperpressing and the 250 kgf/cm² (24.5 MPa) threshold that distinguishes it from ordinary pressing
  • Apply Pascal's law to calculate cylinder force and the specific pressure on a product
  • Identify the main assemblies of a hyperpress and trace the force loop through the frame
  • Explain why double-action pressing gives a more uniform product than single-action pressing
  • Size a press for a given product face area and target output
  • Diagnose common hyperpressing defects and their causes

What a hyperpress is and why it matters

A hyperpress — also called a hydraulic press with high specific forming pressure, or a high-pressure brick and block making machine — is an industrial hydraulic press that compacts a semi-dry mix of inert filler, Portland cement and a little water into small building products such as bricks, blocks, paving units, tiles and roof tiles. By expert consensus the lower threshold of hyperpressing is a specific forming pressure of 250 kgf/cm², about 24.52 MPa, acting on the face of the product.

The inert filler is usually a by-product: screenings of soft sedimentary rocks (limestone, dolomite, shell rock), ash and slag, or crushed demolition waste. Pressing forces the particles into close contact with each other and with the cement, so that after hydration the product is strong, dense and dimensionally accurate without any firing or autoclaving.

≥ 24.5 MPaspecific forming pressure
6–8 %typical mix moisture
3–10 stypical press cycle
20–30 °Ccuring, no kiln

This chapter is the physics and construction reference for hyperpressing. For the wider family of brick technologies see Brick Making Machine; for how high pressure is used across concrete, clay and sand-lime products see High-Pressure Brick Making Machine.

Working principle: from oil pressure to product density

Pascal’s law and the force of a press

A hyperpress is a hydraulic press. Its force comes from one or more cylinders, which act as the hydraulic equivalent of a lever. Pascal’s law states that pressure applied to a confined, stationary fluid is transmitted equally to every point of the fluid. A modest force on a small piston therefore produces a much larger force on a large piston; in exchange, the small piston travels proportionally farther.

p = F₂ / S₂ · F₁ = p · S₁ = F₂ · (S₁ / S₂)p — fluid pressure, Pa; F₂ — force on the small piston, N; S₂ — small piston area, m²; F₁ — force on the large piston, N; S₁ — large piston area, m²

The force amplification equals the area ratio S₁/S₂. In a real press the “small piston” is the pump, which delivers oil at pressure p. The force on the main cylinder is then simply oil pressure times piston area, and the pressure the product feels is that force divided by the face area under the punch.

F = p · A꜀ = p · π · D² / 4 · σ = F / AₚF — press force, N; p — oil pressure, Pa (1 bar = 0.1 MPa); A꜀ — piston area, m²; D — cylinder bore, m; σ — specific forming pressure, Pa; Aₚ — total face area of products under the punches, m²
Pascal's law with two connected pistons, and the chain from pump pressure to cylinder force to specific pressure on the product in a hyperpress
Pascal's law (a) and its use in a hyperpress (b). Note the two area ratios: oil pressure is multiplied by the piston area and divided again by the product face area.

Two practical consequences follow. First, a press develops force only against resistance: while the punch moves through air the oil pressure is low, and it rises only when the mix resists compaction. Second, the maximum force is reached at the highest permitted oil pressure and is directly proportional to the cylinder cross-section — the larger the bore, the greater the force. Standard industrial hydraulics work safely at about 280–350 bar; TITAN brick presses are rated at 230–315 bar. Non-standard systems reach 500–700 bar with hydraulic intensifiers (boosters) or radial-piston pumps, at the cost of more demanding seals, hoses and maintenance.

Worked example — force for one brickA 250 × 120 × 65 mm brick is pressed along its 65 mm dimension, so the punch acts on 25 cm × 12 cm = 300 cm². At the hyperpressing threshold of 250 kgf/cm²: F = 250 × 300 = 75,000 kgf = 75 tf. In SI units, 75,000 kgf × 9.80665 = 735.5 kN, and 735.5 kN / 0.030 m² = 24.5 MPa. The press therefore needs at least 75 tonnes-force for every brick formed in the same stroke.

What happens inside the mix

Compaction of a semi-dry mix proceeds in overlapping stages: particles first slide and rearrange into the voids; then contacts carry rising stress and weak grains fracture, filling smaller voids; finally the grains and the cement paste deform elastically and plastically. Density rises steeply at first and then levels off. Empirically, the void fraction falls roughly exponentially with pressure (the same behaviour that powder technologists describe with Heckel-type equations).

Typical curves of pressed density and compressive strength against specific forming pressure from 0 to 50 MPa, with the hyperpressing zone above 24.5 MPa shaded
Typical trend of density and 28-day strength with forming pressure. The steep part of the curve lies below about 15 MPa; above 35–40 MPa each extra megapascal buys very little.

Water plays two roles. A film of moisture lubricates the grains and lets them pack closely, and it is needed later for cement hydration. Too much water, however, fills the pores; because water is almost incompressible, the pore pressure then carries part of the load, water is squeezed to the surface and the product may crack on unloading. This is why each mix has an optimum moisture, usually 6–8 %.

Wall friction and the case for double action

Friction between the mix and the mould wall consumes part of the punch force, so the pressure — and therefore the density — falls with distance from the moving punch. For a column of granular material the decay is approximately exponential (the Janssen relationship): σ(z) ≈ σ₀ · exp(−4 μ K z / d), where μ is the wall friction coefficient, K the ratio of lateral to vertical stress, z the distance from the punch and d the cavity’s hydraulic diameter. The taller and narrower the product, the larger the loss.

In single-action pressing only the upper punch moves and the bottom of the product is the least dense. In double-action pressing both punches move towards each other inside a fixed mould; each punch only has to push through half the height, and the lowest-density layer — the neutral plane — lies at mid-height. TITAN D-series machines (80D, 240D, 400D, 600D) are double-action presses; S-series machines such as the TITAN 240S and 80S are single-action presses.

Comparison of density distribution in single-action and double-action pressing, with wall friction arrows and density-height profiles
Single-action versus double-action pressing. The red arrows show wall friction on the mix; darker shading means higher density. Double action halves the friction path and produces a symmetric profile.

Machine construction

A hyperpress is built around a closed force loop. The upper cylinder sits on the upper crosshead and pushes its punch down; the lower cylinder sits on the base and pushes its punch up. The product between the punches is in compression, and the reaction travels through both crossheads into the tie columns, which are in tension. Nothing else in the machine — not the mould, not the floor — carries the pressing force.

The main assemblies are:

  • Frame — either a classical four-column frame with machined crossheads and preloaded tie columns, or a welded frame with a guiding system. Large TITAN presses such as the 1000D and 1600D use cast or forged crossheads on four prestressed pillars.
  • Main (upper) cylinder and lower cylinder — in a double-action press both are active; the lower one also ejects the product. A prefill valve lets the cylinder draw oil quickly from a tank during the fast approach.
  • Mould — a mould block or frame, held stationary during compaction, with hardened replaceable wear liners forming the cavities.
  • Punches — upper and lower punches with hardened faces on punch plates; their shape forms the product’s faces, perforations and interlocking profiles.
  • Feeder and hopper — a feeder box slides across the mould, fills the cavities by volume and pushes the finished products onto the take-off table.
  • Hydraulic power unit — tank, electric motor, pumps, proportional valves, filtration and oil cooling (TITAN brick presses are typically connected to cooling water at 2–4 m³/h).
  • Control system — a PLC with pressure transducers and position sensors on the rams, which runs the cycle and stores a recipe for each product.
Labelled vertical section through a double-action hyperpress mould showing rams, punch plates, punches, mould block, wear liners, product, fill height and neutral plane
Section through the mould at the end of compaction. Compare the dashed loose-fill outline (h₀) with the pressed product (h): their ratio is the compression ratio.
TITAN 240D hydraulic press, front view with front press opening, chrome columns and separate blue-motor power unit
Example: the TITAN 240D, a four-column double-action hyperpress rated at 251,000 kgf. The yellow upper and lower crossheads, the tie columns and the separate hydraulic power unit are visible.

The operating cycle step by step

Every product is made in the same short sequence, repeated several times per minute:

  1. Fill — the lower punch drops to the fill position; the feeder box moves over the mould and fills the cavities by gravity. The fill depth sets the mass of mix per product.
  2. Strike off — the feeder returns, scraping the mix level with the top of the mould.
  3. Pre-press and de-air — the punches close at low force; air escapes through the punch–liner clearance. A short pause or two-stage pressing reduces trapped air.
  4. Final compaction — both punches move towards the neutral plane until the set pressure (typically 25–40 MPa) or the set product height is reached, followed by a short dwell and a controlled pressure release.
  5. Ejection — the upper punch withdraws and the lower punch lifts the product to table level.
  6. Take-off and refill — the feeder pushes the product onto the take-off table or stacker and, in the same movement, fills the mould for the next cycle.
Six panels showing the hyperpress cycle: fill, strike off, pre-press and de-air, final compaction, ejection, take-off and refill
The six steps of a hyperpress cycle. Watch the lower punch: it sets the fill depth in step 1, presses in step 4 and ejects in step 5.

Cycle times range from about 3–4 s on a fast single-cavity press such as the TITAN 80S to 10–25 s for large blocks and tiles. Hourly output is Q = 60 · n · N, where n is strokes per minute and N the number of products per stroke.

Raw materials, mix design and products

Typical hyperpress mix components (general practice; every mix must be confirmed by trials).
ComponentTypical shareRole and notes
Limestone, dolomite or shell-rock screenings, 0–5 mm80–90 %Main filler; soft rocks compact well and give a fine, even surface
Fly ash, slag, crushed demolition wastepartly or wholly replaces rockLowers cost and recycles waste; check grading, sulphates and free lime
Portland cementabout 7–15 %Binder; strength develops by hydration after pressing
Water6–8 % (4–12 % in special cases)Lubricates packing and hydrates cement; must be controlled to ±0.5 %
Pigment (iron oxides)2–5 % of cement massColour for facing bricks; usually only in a face layer

Grading matters as much as composition: a continuous particle-size curve with enough fines fills the voids and needs less cement. Mixing should be intensive and the moisture measured continuously, because a 1 % change in water shifts both density and product height.

Product range of hyperpresses.
ProductTypical sizesNotes
Solid and perforated bricks250 × 120 × 65 / 88 mm, 215 × 102.5 × 65 mmFacing bricks with smooth or “split rock” faces
Interlocking (“Lego”) brickse.g. 250 × 125 × 100 mmMortarless or thin-bed masonry
Wall blocksup to 600 × 300 × 220 mm (TITAN 600DH)Hollow cores formed by punch cores
Paving units and tilesup to 600 × 600 mm (TITAN 400D)Two-layer products possible
Kerbstonesup to 1,000 × 200 × 300 mm (TITAN 600D)Large face area: highest force demand

Key parameters and how to size a hyperpress

Main parameters of TITAN D-series hyperpresses (manufacturer's data).
Parameter80D240D400D600D
Press force, kgf92,000251,000420,000630,000
Max. oil pressure, bar230297297297
Filling depth, mm165220—310
Strokes per min (nominal brick)101065
Ejection force, kgf12,00020,00051,00074,000
Connected load, kW15253795

Choose a press in this order:

  1. Product face area and target pressure fix the force per stroke (F = σ · Aₚ). Use 25–30 MPa for ordinary bricks and blocks and more for dense facing or paving products.
  2. Filling depth must hold the loose fill: h₀ = k · h, with k ≈ 1.6–2.0. A 65 mm brick needs roughly 105–130 mm; a 200 mm block 320–400 mm unless pressed on its side.
  3. Mould area limits the number and size of products per stroke.
  4. Stroke rate and cavities give the output; check that the mixer, feeder and stacker can keep up.
  5. Reliability and service — spare parts, liners and punches are consumables; payback depends on keeping the press running.
Chart of required press force against total punch face area for 20, 25, 30 and 40 MPa, with the nominal forces of TITAN 80D, 240D, 400D and 600D marked
Required press force against punch face area. Where a pressure line crosses a machine's force line you can read the largest face area that machine can press at that pressure.
Worked example — sizing for a brick plantTarget: 250 × 120 × 65 mm bricks at about 27 MPa, 22,000 bricks per 16-hour day. Face area per brick 0.030 m²; three bricks per stroke give Aₚ = 0.090 m². Required force F = 27 MPa × 0.090 m² = 2.43 MN = 248 tf, so a 251 tf press (the TITAN 240D class) is suitable and gives σ = 2,461 kN / 0.090 m² = 27.3 MPa. At 9 strokes per minute: Q = 60 × 9 × 3 = 1,620 bricks/h. With 85 % availability, 1,620 × 0.85 × 16 h ≈ 22,000 bricks per day. Filling depth needed: 1.8 × 65 mm ≈ 117 mm, well inside 220 mm.

Comparison with other forming technologies

Hyperpressing compared with the main alternative brick technologies (typical values).
HyperpressingVibro-pressingExtrusion + firing (clay)Pressing + autoclave (sand-lime)
Forming pressure25–40 MPa staticvibration + low static loadplastic extrusion, about 1–4 MPa in the dieabout 15–25 MPa
Mix moisture6–8 %earth-moist concrete15–25 %about 5–7 %
Hardeningcement hydration at ambient temperaturecement hydration, often steamdrying and firing at 900–1,100 °Csaturated steam, about 180–200 °C
Dimensional accuracyvery highmoderatemoderate (firing shrinkage)high
Strengthswaste raw materials, low energy, sharp edgeslarge blocks, many per cycleproven ceramic durabilitywhite, precise units
Limitscement needed; product height limited by frictionlower density, rougher faceshigh fuel use, clay neededautoclave capital, lime needed

Hyperpressing is strongest where suitable rock screenings or wastes are available and accuracy matters. Vibro-pressing remains more economical for large hollow blocks; sand-lime technology is described in the sand-lime brick making machine chapter.

Quality, defects, maintenance and safety

Common hyperpressing defects.
DefectTypical causesRemedy
Horizontal lamination crackstrapped air; too-fast decompression; over-pressing; too many finesadd de-airing stage; slow pressure release; check grading
Height variationuneven fill; moisture changes; worn feedercontrol moisture; maintain feeder; use position control
Low strength or soft bottom layerlow pressure; low cement; dry mix; single action on tall unitsraise pressure or cement; adjust water; press double-action
Chipped edges and cornersworn liners; misaligned punches; rough handling at take-offreplace liners; re-align; adjust ejection speed
Surface water, cracks after ejectionmoisture above optimumreduce water; check moisture sensor
Efflorescencesoluble salts; excess water; poor curingcontrol raw materials; cure under cover

Good practice follows the operating tips that have always applied to hyperpresses:

  • Inspect and maintain regularly — oil level and temperature (usually 40–55 °C), filter condition, hose and seal integrity, accumulator pre-charge. Early detection extends the life of the press and the quality of the products.
  • Clean the moulds — remove residual mix from punches and liners every shift so that product shape stays constant and wear does not accelerate.
  • Control the mix — keep the ratio of filler, cement and water constant; the formula fixes density and quality.
  • Train the operators — skilled staff spot drifting pressures, heights or surface defects early and keep the press safe.
SafetyA hyperpress stores large amounts of hydraulic energy. Never reach into the mould or feeder area unless the press is stopped, locked out and the accumulators are depressurised. Keep all guards and light curtains working, support raised punches mechanically during tool changes, and never loosen a hydraulic fitting under pressure.
Summary
  • A hyperpress compacts a semi-dry mix at 24.5 MPa (250 kgf/cm²) or more; strength then develops by cement hydration without firing.
  • Force = oil pressure × piston area; specific pressure = force ÷ product face area.
  • Density rises steeply up to about 15 MPa and levels off above 35–40 MPa; moisture has an optimum near 6–8 %.
  • Wall friction causes density gradients; double-action pressing halves them by placing the neutral plane at mid-height.
  • The press force is carried in a closed loop: punches and product in compression, tie columns in tension.
  • Size a press from face area, target pressure, filling depth, mould area and stroke rate.

Key terms

Hyperpress
A hydraulic press that forms small building products from a semi-dry mix at a specific pressure of at least about 24.5 MPa (250 kgf/cm²).
Specific forming pressure (σ)
Press force divided by the face area of the product under the punch; the figure that governs density, expressed in MPa or kgf/cm².
Semi-dry mix
A granular mix with typically 6–8 % moisture (4–12 % in special cases) that is pressed, not cast or vibrated.
Double-action pressing
Pressing in which the upper and lower punches both move towards each other inside a fixed mould, placing the neutral plane at mid-height.
Neutral plane
The layer inside the product that does not move relative to the mould wall during pressing; it has the lowest density.
Compression ratio (k)
Loose fill height divided by pressed product height, typically 1.6–2.0 for semi-dry mixes.
Force loop
The closed path of load through punches, cylinders, crossheads and tie columns; the columns are in tension while the product is in compression.
Lamination
Horizontal cracks in a pressed product, usually caused by trapped air or by releasing the pressure too quickly.
Wear liner
A hardened, replaceable steel lining of the mould cavity that takes the abrasion of the mix.

Check your understanding

What pressure does a hyperpress use?

Hyperpressing conventionally starts at 250 kgf/cm², which is about 24.5 MPa on the face of the product. Most production work is done between about 25 and 40 MPa. Above roughly 35–40 MPa the gain in density becomes small while wear and energy use keep rising.

Can a hyperpress make blocks as well as bricks?

Yes. With interchangeable moulds the same press can make solid and hollow bricks, facing bricks, wall blocks, paving units and tiles. The limits are the mould area, the filling depth and the force needed to reach the target pressure on the larger face area.

How do you calculate the press force needed for a brick?

Multiply the target specific pressure by the face area under the punch. A 250 × 120 mm brick has a face area of 300 cm²; at 250 kgf/cm² it needs 75,000 kgf, which is 75 tonnes-force or 735.5 kN. Multiply by the number of products pressed per stroke.

Do hyperpressed bricks need firing or autoclaving?

No. The strength comes from cement hydration in a very dense body, so the bricks harden at ambient temperature or with mild steam curing. This is one reason the process uses little energy compared with fired clay or autoclaved sand-lime bricks.

Why does the hydraulic pressure in the press differ from the pressure on the brick?

The oil pressure acts on the large area of the main cylinder piston, while the resulting force is spread over the smaller face of the product. The ratio of the two areas sets the difference; for example 300 bar on a 320 mm bore gives about 27 MPa on three standard bricks.

What raw materials are used in a hyperpress?

Mainly screenings of soft sedimentary rocks such as limestone, dolomite and shell rock, plus industrial wastes such as ash, slag and crushed demolition waste. They are bound with Portland cement and a small amount of water.

TITAN equipment for this topic
Further reading

Talk to a TITAN engineer

Send us your raw materials, product sizes and target output. We will recommend the process, the machines and the plant layout.

Ask an Engineer