Brick Machine Assembly: How to Assemble the TITAN 80S4 Hyperpress Step by Step
Brick machine assembly guide for the TITAN 80S4 hyperpress: levelling the base, guide plates, lower platen, hydraulic tank, main and quick-motion cylinders.
- Assembly runs in three stages: lower section, hydraulic tank, then main and auxiliary cylinders.
- The base must be levelled perfectly horizontal and the guide plates fixed perfectly vertical.
- The hydraulic tank is cleaned and inspected before mounting; lines follow the schematics and are leak-checked.
- The main cylinder is aligned precisely with the guide columns; quick-motion cylinders provide fast strokes.
- Finish by testing all hydraulic and mechanical systems before production.
Correct brick machine assembly is the foundation of a hyperpress that runs reliably for years. For the TITAN 80S4 hyperpress, assembly follows three main stages: the lower section of the press, the hydraulic tank, and the main and quick-motion auxiliary cylinders. This guide explains each stage, what to check and why it matters for the precision of the finished bricks.
Why careful assembly matters
A hyperpress compacts the mix under very high pressure in a steel mould. The punch must enter the mould cavity exactly on axis, stroke after stroke. If the base is not level or the guides are not vertical, the punch and mould wear unevenly, the bricks vary in height and the hydraulic seals carry side loads they were never designed for. Leaks or dirt in the hydraulic system cause the next set of problems: slow cycles, pressure loss and premature wear of pumps and valves.
Following the sequence below, step by step and without shortcuts, — and the technical documentation supplied with the machine — avoids these issues from day one.
Before you start: preparation checklist
Good assembly starts before the first component is lifted. Make sure that:
- the foundation is ready — cured, clean, level and built to the drawing supplied with the machine;
- lifting equipment is available — a crane or hoist rated for the heaviest component, with suitable slings;
- documentation is at hand — assembly drawings, hydraulic schematics and the technical manual;
- the work area is clean — dust and grit are the enemy of hydraulic components, so keep hoses, ports and cylinders capped until the moment of connection;
- tools and measuring instruments are ready — spirit level or precision level, torque wrench and the fasteners listed in the parts list.
Stage 1: Assembling the lower section of the hyperpress
- Install the base. Place the base of the press on the prepared foundation and level it. Use a levelling tool to make sure it is perfectly horizontal.
- Mount the guide plates. Attach the vertical guide plates securely to the base and make sure they are perfectly vertical. Correct alignment is essential for precise operation of the press.
- Install the lower platen. Fix the lower platen onto the base and check that it is correctly positioned relative to the guide columns. Verify that it is firmly secured to avoid misalignment during operation.
Stage 2: Assembling the hydraulic tank

- Prepare the tank. Clean the inside of the hydraulic tank to remove any debris or contaminants, and inspect it for damage or defects. Cleanliness here protects every pump, valve and seal downstream.
- Position the tank. Place the hydraulic tank in its designated location on the press, with secure mounting and proper alignment.
- Connect the hydraulic lines. Attach the hoses and pipelines to the correct ports on the tank. Follow the supplied schematics to ensure correct connections, then check for leaks.
Stage 3: Installing the main cylinder and quick-motion auxiliary cylinders
The 80S4 uses a main cylinder for the pressing stroke and quick-motion auxiliary cylinders for fast movements. Splitting the work this way keeps the cycle short: the small cylinders move the press quickly, and the main cylinder delivers the force.
| Component | Preparation | Installation | Hydraulic connection |
|---|---|---|---|
| Main cylinder | Inspect for damage or leakage | Mount on the upper platen, aligned precisely with the guide columns | Connect lines as per the technical documentation |
| Quick-motion auxiliary cylinders | Inspect for function and damage | Secure in their designated positions on the press | Attach lines; all connections tight and leak-free |
The main cylinder is the most heavily loaded part of the press. Read why TITAN makes it from solid forgings.
General recommendations for safe, accurate assembly
- Follow the technical documentation. Always refer to the manufacturer’s instructions and drawings so that every step meets the technical specification.
- Safety first. Use appropriate personal protective equipment (PPE) and follow safety procedures throughout, especially when lifting heavy components such as the cylinder.
- Test and validate. When assembly is complete, test all systems — hydraulic and mechanical — to confirm correct operation before starting production.
Common assembly mistakes to avoid
- Skipping the final alignment check. A base that was level before tightening may not be level after it.
- Removing protective caps too early. Open hydraulic ports collect dust within minutes; contamination is a leading cause of valve and seal wear.
- Connecting lines from memory. Always follow the schematics — a swapped line can make a cylinder move the wrong way on first start-up.
- Rushing the first test. Start the hydraulics at low pressure, check every joint for leaks and only then move to full working pressure.
Get support for your TITAN hyperpress
By following these steps and recommendations, you ensure reliable and efficient operation of your TITAN 80S4 hyperpress. For additional guidance, consult the technical manual or contact TITAN support. Learn more about the machine family on the TITAN 80S brick making machine page.
Frequently asked questions
What is the first step when assembling a TITAN 80S4 hyperpress?
Place the base of the press on the prepared foundation and level it with a levelling tool until it is perfectly horizontal. All later alignment depends on this.
How should the hydraulic tank be prepared?
Clean the inside of the tank to remove debris and contaminants, inspect it for damage or defects, mount it securely in its designated position, then connect the hoses and pipelines according to the schematics and check for leaks.
What are the quick-motion auxiliary cylinders for?
They perform the fast, low-force movements of the press so that the main cylinder only has to deliver the high-pressure pressing stroke. They must be inspected, secured in their positions and connected with tight, leak-free hydraulic lines.
What should be done after assembly?
Test all systems, including the hydraulic and mechanical components, to confirm proper operation. Always follow the technical documentation and use appropriate PPE throughout.


